Fujioh BUF-08P User Manual download pdf

∅6-15/16"

44"

29-9/16"

∅1/4"

Holes for mounting range hood

∅9/16"

8-1/4"

9-5/16"

2-7/16"

43"

1/16"

10-13/16" 6-1/8"

31-3/4"

17-7/8"

45"

17-7/8"

16-3/4"

10-7/16"

∅7/8"

9/16" 14" 3-1/8"

2-3/16"

Roof cap

Duct

(For vertical discharge)

Range hood

Wood hood

Soffit

Note:

2×7" or 1×10"~12"

round duct

Duct

(For holizontal

discharge)

Note:

2×7" or

1×10"~12"

round duct

Wall cap

Fan Switch

(Right)

Fan Switch

(Left)

Front Cover

Enclosure

Filter

Lamp Switch

High Switch

Medium SwitchLow Switch

OFF Switch

Pilot Lamp

Lamp (Not supplied)

(PAR20 bulb,

in the base diameter

26mm: medium base)

INSTALLATION MANUAL

Model: BUF-08P

1U03 2783

Before installation and operation, read these instructions carefully

and use this product only in the manner described by the

manufacturer in the operation manual.

The instruction shown below are used to alert you to potential

personal injury and property damage hazards.

There are three hazard classifications based on potentially

dangerous situations.

Obey all safety instructions that show these symbols to avoid

possible injury, death and property damage.

SAFETY INSTRUCTIONS

WARNING:

WARNING indicates a potentially

hazardous situation which, if not

avoided, could result in death or

serious injury.

CAUTION:

CAUTION indicates a potentially

hazardous situation which, if not

avoided, may result in minor or

moderate injury.

NOTE

: The safety instructions are explained with the following

pictographic symbols.

means forcible execution. It indicates actions,

if any, that must be done.

WARNING

1. TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

a) Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

b) Before servicing or cleaning unit, switch power

off at service panel and lock the service

disconnecting means to prevent power from being

switched on accidentally. When the service

disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag,

to the service panel.

CAUTION

INSTALLATION

1. Preparation

2. Range Hood Mounting

3. Connecting Power Supply Wires

Remove the nut from the conduit

connector at the end of power wiring.

Remove one screw fixing the

wire cover then slide it to detach.

4. Final Assembly and Check

Range Hood

3. Read specification label on this product for further

information and requirements.

2. To reduce the risk of fire and to properly exhaust

air, be sure to duct air outside. Do not vent exhaust

air into spaces within walls or ceilings or into attics,

crawl spaces, or garages.

6. Fasten the filter and other parts securely. Incorrect

attachment may result in personal injury or

property damage.

4. Use only for the purpose of kitchen ventilation.

1. For general ventilating use only. Do not use to

exhaust hazardous or explosive material and

vapors.

5. Do not install this range hood in the bathroom or

in other wet rooms since electrical shock and

damage may result.

2. To reduce the risk of fire or electric shock, do not

use this product with any solid-state speed control

device.

b) Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney)

of fuel burning equipment to prevent back drafting.

Follow the heating equipment manufacturer’s

guidelines and safety standards such as those

published by the National Fire Protection

Association (NFPA), and The American Society

for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code

authorities.

c) When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

d) Ducted fans must always be vented to the

outdoors.

e) The end user is responsible to ensure compliance

with all Federal, State and Local Environmental

and Fire codes.

According to the conditions

where the range hood is

installed, determine whether it

will be discharged vertically or

horizontally. For vertical or

horizontal discharge, run duct

work between the hood location

and the roof cap or wall cap.

For best result in either direction,

use a minimum number of

transitions and elbows. Be sure

to attach a roof cap or wall cap

to avoid rain/wind entry.

The range hood unit

must be mounted to a

liner which has the

following dimensions.

Install the liner

securely after

checking that the

opening size of the

liner is the same as

the figure.

• If the range hood is not installed properly, it could become detached and

fall.

• Ensure that the metal duct does not touch other metal housing materials,

otherwise fire or electric shock could result.

• When the liner is installed in the wooden hood, the inside of the wooden

hood placed above the cooking surface must be fully covered by the metal

barrier including bottom edges. Select a suitable liner and metal barrier

according to the size and shape of the wooden hood and install properly.

• The liner should be installed tightly. If the liner installation is not correct,

the range hood unit may become detached and fall.

• Wear working gloves to avoid injury.

CAUTION:

5. Explanation to the End User

(1) Referring to the Operation Manual, explain the operation of this range

hood to end users.

(2) The Installation Manual and Operation Manual should be given to the

end user.

Check

(1) Turn on the electrical circuit to the range hood.

(2) Make sure that the switches and light operate correctly.

Refer to page 4 of the Operation Manual.

(3) Make sure that the range hood functions properly and it has

no abnormal noises and/or vibration.

• Electrical wiring should be done by a qualified person(s) in accordance

with all applicable codes and standards, including fire-rated construction.

An unqualified person doing the work could result in fire, electric shock

or injury.

• This range hood uses 120V AC. Do not connect to other voltage since

fire, electric shock or damage could result.

Be sure to switch power OFF

at service panel before wiring.

Connect the conduit through

the connecting hole of the

enclosure using the nut

previously removed.

Connect wires tightly and securely

using wire connectors (not supplied).

Connect the electrical wires as follows:

Replace the wire cover with

sliding it as shown and using

the screw removed previously.

Make sure that all wires are

connected properly and

enclosed inside of the wiring

compartment.

Align 4 screw holes of the liner and range hood, then fix securely

using the supplied screws (M5×30) and nuts.

Note:

Fasten all the screws and nuts evenly.

CAUTION:

CAUTION used without the safety

alert symbol indicates a potentially

hazardous situation which, if not

avoided, may result in property

damage.

means prohibition. It indicates actions, if any,

that mustn’t be done.

4. TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

5. This unit must be grounded.

CIRCUIT DIAGRAM

6. Install this range hood to a liner. Check that the

hood is correctly installed, since incorrect

installation could result in the range hood

becoming detached and falling off.

7. Connect only to an AC120 Volt power source or

the range hood could result in fire, electric shock,

and damage.

DIMENSIONS

CAUTION:

WARNING:

(Unit: inch)

NAMES OF PARTS

RANGE HOOD LOCATION

The range hood must be installed just

above the cooktop.

The minimum distance from the

cooking surface to the bottom of the

range hood must be 24".

The total weight of the BUF-08P

range hood unit is 70.4 lbs. (32 kg)

Power requirements are:

AC120 V, 60 Hz, 5.8 Amp

• Check that the hood is correctly installed, since incorrect installation

could result in the detachment of the range hood and the unit could fall.

WARNING:

ACCESSORIES

Screw M5×30

Four (4) pieces

Nut with plate

Four (4) pieces

Mounting bracket

One (1) piece

24" (Minimum)

Cook top

Liner

FWD switches & lamps side

44"

8-1/4"

4-∅1/4"

Holes for mounting

range hood

Center line

Front

Liner Dimensions

(Unit: inch)

Liner

Range hood cutout

43-3/16"

16-7/8"

Exhaust

port

Front cover

Filter

Loosen screws

to remove the filters.

Conduit

(Not supplied)

Nut

(Not supplied)

Wire cover

Hook

Lamp SwitchFan Switch

Push to

turn ON

Turn the switch

clockwise

120V

60Hz

Connector

Motor

Red

Orange

White

Black

Blue

Brown

Red

Orange

White

Blue

Brown

Red

Orange

White

Black

Blue

Brown

Red

Orange

White

Blue

Brown

Orange

Blue

Brown

Black

White

Black

White

Black

White

Green

Black Black

Grey

Black

BlackYe l l o w

Yellow

Yellow Black

Black

Pilot Lamp

Lamp:50W

Fan Switch

Capacitor

Lamp Switch

Purple

Washer

Bracket

Not supplied

Spring-washer

Nut

Mounting bracket

Beam

Put 4 all thread rod (∅1/2” anchor bolt, not supplied) into the corner

holes of the mounting bracket, and secure them using washers, spring

washers, and nuts. Place the mounting bracket on the beam of the

ceiling as shown.

3. TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE

THE FOLLOWING:

a) Installation work and electrical wiring must be

done by a qualified person(s) in accordance with

all applicable codes and standards, including fire-

rated construction.

• Black to Black

• White to White

• Green to Green

WARNING:

The following method is the standard installation.

There may be some different cases depending on the structure of

the ceiling where the mounting bracket is placed or the shape and

mounting condition of the wood hood.

In such a case, please arrange best possible way according to the

condition of the place where the range hood is being installed.

Detach

the tape.

Tape

Clamper

Keyhole

Clamper

Fan unit

Keyhole

FWD

Remove first

Remove second

Using washers, spring washers, and double nuts, attach the range

hood to all 4 threaded rods securely.

Hold up the range hood,

and with inserting the

exhaust port into the duct,

pass all 4 threaded rods

through the corner holes of

the range hood.

Note:

Do not touch the switch

buttons when holding the

unit as damage may result.

Note:

The mounting bracket should be securely fastened at this point

to simplify installing the range hood later.

Place the range hood

as shown and detach

all filters by loosening

screws.

Then remove 6 screws

fixing the front cover

and detach the front

cover.

Note:

Pay attention not

to deform the

exhaust ports.

Note:

If taping from the outside is impossible, remove the exhaust port

and insert the duct end to the range hood directly, then make

inside taping on the duct end. Be sure to attach a duct cover with

damper in this case.

Duct

Non-flammable

tape

Range hood

Duct

Exhaust port

Washer

Enclosure

Use less than ∅1"

washer to avoid

overlapping with

the enclosure bend.

Spring-

washer

Nut

Not supplied

∅

1"(

∅

25.4)

7. Keep your hands and other objects away from

the fan while it is in motion. The range hood may

injure you or damage itself.

Turn over the range hood and detach

the tape on the exhaust ports.

Note:

Do not remove the keyhole screws.

(3) Remove screws attaching to the top plate.

(4) Disconnect wiring connector coming from the fan unit.

(5) Slide the fan unit rightward to disengage from fixing hook,

then pull it up while avoiding keyhole’s screws to remove from

the range hood.

FWD

Connector

Slide

Remove this side unit

Hook

Screw

Connector

Push with a

screwdriver etc,

and pull off.

Liner

[Securing plate

turns while

passing through

the opening

of Liner]

Securing plate

Nut with plate

[Right & left, each two (2) places]

Nut with plate

Four screws

(M5×30)

Slide

Hook

Screw

Attach this side unit

Bracket

Fan unit

Wire

Keyhole

FWD

(6) Three 50 Watt halogen light bulbs (not supplied)

can be mounted in this range hood.

Assembly

(1) Attach the fan units respectively by sliding

them leftward to engage with bracket hooks

and keyholes, then tighten screws.

Note:

Pass through the wiring over the bracket.

(5) Attach the front cover, and secure

it with 6 screws.

Then attach the filters.

Prior to function check, install

light bulbs (PAR20 bulb, with

base diameter 26 mm: medium

base), rated at 120 V - 50 Watt

or below.

Screw

Filter

Front cover

Bulb

(Not supplied)

Remove the fan units.

Make the duct joints secure and air-tight using non-flammable tape

such as duct tape, etc. (Not supplied)

Non-flammable tape

(2) Fix each fan unit using the

removed screws.

(3) Connect each fan unit’s

wiring connector.

Note:

Be sure to connect

firmly as illustrated.

(4) Fasten each fan unit’s

wiring clamper.

Connector

Clamper

FWD

Connector

Clamper

Note:

During installation, be careful not to

touch the fan switches. If two or more

switches are pushed at once, it may

be a cause of failure.

(1) Release each fan unit’s

wiring clamper.

(2) Remove total 4 screws

from each unit.

Fan unit Fan unit

Remove this unit first

FWD

Fan unit Fan unit

Attach this unit first

FWD

Check that the fan unit is hanged securely on

the keyhole screw and fixing hooks when

attaching. It may be a cause of injury if dropped.

CAUTION:

The following light bulbs are recommended for this range hood.

• GE Model No. 50PAR20H/FL25

• SYLVANIA Model No. 50PAR20/HAL/DL/NFL

Turn the lamps clock-wise to install.

• To protect hands from injury, wear working gloves when installing the

range hood.

CAUTION:

• The liner shape illustrated in this installation manual is only for reference.

1 2

Summary of Contents

Page 1 - INSTALLATION MANUAL

∅6-15/16"44"29-9/16"4-∅1/4"Holes for mounting range hood4-∅9/16"8-1/4"9-5/16"2-7/16"43"1/16"10-13/16

Page 2 - MANUEL D’INSTALLATION

6-15/16"44"29-9/16"4-1/4"Trous pour le montage de la hotte d’aspiration4-9/16"8-1/4"9-5/16"2-7/16"43"1/16

Comments to this Manuals

No comments

Fujioh BUF-08P User Manual

Browse online or download User Manual for Fans Fujioh BUF-08P. Fujioh BUF-08P Manuel d'utilisation

Summary of Contents

Comments to this Manuals